VW Parts For Sale...Make offer!

I went thru the engine top end so I could replace the tubes and seals...they were dinged and rubber was brittle.Also cleaned up the heads a little and checked valve movement on the bench.It rotates smoothly.6 v Flywheel is on it. New v/c gaskets and strainer gaskets,washers.Timing was set when I had it running,so it should be OK.
Exhaust is Bugpack 1 5/8 merged with Phat Boy.The DH 36hp shroud goes with,but I don't have the DH cooler.
I have heater boxes,stock 1300 or 40hp shroud,stock coil,carb,generator...how ever you want to set it up.
It was going to be a Rat engine for the '67 pan/68 body that I have all the metal to make it into a '67,or '66 body...I'm undiagnosed A.A.D.D.,so I need to keep on 1 project,or nothing will be finished.LOL

Some more 61 parts outta the attic...
The Snowflakes have all the brackets and bulb holders in them.Housings are solid,and kinda ratty,but you may like them that way.$50
The car sat for about 30 years.
The decklid light is hanging on with one bolt up top,but they still make them.Latch is all there and works,no bondo that i see in the lid.$75
Wiper assem and arms are OG and 6 volt probably.$25

I have these new wheels and tires for sale too...This was the 61 the parts came from.
Front tires are new Nitto Xtreme 195-50,rears are used Goodyear 21-65...$400 set.

JEFF KYLE wrote:I went thru the engine top end so I could replace the tubes and seals...they were dinged and rubber was brittle.Also cleaned up the heads a little and checked valve movement on the bench.It rotates smoothly.6 v Flywheel is on it. New v/c gaskets and strainer gaskets,washers.Timing was set when I had it running,so it should be OK.
Exhaust is Bugpack 1 5/8 merged with Phat Boy.The DH 36hp shroud goes with,but I don't have the DH cooler.
I have heater boxes,stock 1300 or 40hp shroud,stock coil,carb,generator...how ever you want to set it up.
It was going to be a Rat engine for the '67 pan/68 body that I have all the metal to make it into a '67,or '66 body...I'm undiagnosed A.A.D.D.,so I need to keep on 1 project,or nothing will be finished.LOL

Calling dibs !

Ok if they want the engine.... I'll take the wheels .. and maybe the tail lights.

when can we come pick up and look @ the 55 ??


And that 61 is sweet I want it !

OK...All on hold till OS gets here. No deposit necessary...
Thanks!

OK see you Sat. Morn early....Ready for the blue light special.....

OK,
The attic is getting clearer...I've got all kinds of engine tin,dual and single port...flaps,thermostat,heater boxes,stock wheels,61-67 tanks,steering wheels,brake drums,
a Mofoco built adjustable Linkpin Beam-Puma type,but not narrowed yet,with stock spindles and arms,no leaves.It should be easier to narrow since the adjusters are in it?
a 6 volt battery cover,jacks,headlight assemblies for earlies...ratty,but there,
Custom made fiberglass rear speaker panels,wire cover,and kick panels for speakers...Also Old Skool Empi 'glass side scoops.
ratty Sapphire IV and V radios with plates and knobs...at least they fill a hole,uncut dash sections from 61,66,67 bugs,a wide five14" bus whee! and cap!...ashtrays front and rear,
a 2" KCW tranny raise kit and new bus nosecone so it lowers the shifter rod...I have it on a spare 68 swingaxle case,4:12 gears, so you can see it mocked up.Old Bugpack shifter,
a 61 trans I put new seals/nuts on and detailed,4:37 gears...and I'm still looking for MIA stuff...I have a Motometer panel for the 55 somewhere...

61 tranny $$$ ?

61 is $150 with spiders...that's core value for my KCR trans I got,but don't want to pay tp mail it to Cali...

More junk...56-60 tank,61-67 tanks,pop-outs for 65 up bug,need new rubbers of course.

I don't have that much money ... stop posting all this B4 Renee sees it and don't let me go Sat....

Well,I have a no credit check program just for you...
If you need something and don't have the cash,you can get it to me later.
I'm not selling stuff for the $$,it needs to be out of my way,but I don't want to just give it away.junk's hard to find...

"ratty Sapphire IV and V radios with plates and knobs...at least they fill a hole"

OS make sure Wilmer looks @ those....
SEE I am NOT the only one that thinks the hole needs to be filled instead of covered w/a plate.

Need to check in the shop, but I may need DP fan housing and heater boxes if they are in good shape.

Heater boxes...levers move well,and no busted exhaust flanges/connections.

I have a couple sets of DP tin...one cleaned/painted,and one grungy

They look fine to me.